Pioneerpos AT Commands G24-LC Instrukcja Użytkownika Strona 382
- Strona / 444
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Call Control
4-14 G24-L AT Commands Reference Manual April 15, 2008
Call Control
The following figure is a detailed view of the states the G24-L goes through for Voice and CSD
Data, as shown in Figure 4-2. Note that between the time the OK is received and the actual
connection occurs, call state alerts are received.
Figure 4-10: Call States
Dialing Using ATD
atd+44 34 56 78; // VOICE call; number includes international access code
OK
OK
atd17085763400; //Second VOICE call
OK
OK //Call to 44345678 is being put on hold
ath //Hang up active call
NO CARRIER
OK
AT+CHLD=0 //Hang up held call
NO CARRIER
OK
atd+44 34 56 78 //DATA call
...
OK //Move to online Data state
//ESC sequence back to the Command state. +++ is sent from the
terminal (+++ is not displayed)
ath //Hang up data call
NO CARRIER
OK //Data call terminated
AT+FCLASS=1
OK
atd+44 34 56 78 //FAX call
...
NO CARRIER //Fax call was terminated by remote side
Idle
Dial
Connected
Alert
Released
Hold
- Technical Information 1
- Copyrights 2
- Computer Software Copyrights 2
- Trademarks 3
- Table of Contents 5
- Table of Contents 10
- List of Figures 13
- List of Figures 14
- List of Tables 15
- List of Tables 16
- Manual Scope 21
- Target Audience 21
- Manual Organization 21
- Applicable Documents 22
- Contact Us 22
- Text Conventions 22
- General Safety 23
- Keep away from live circuits 24
- Batteries 24
- Caring for the Environment 25
- Limitation of Liability 26
- Warranty Notification 27
- How to Get Warranty Service? 27
- Claiming 28
- Installed Data 29
- Out of Warranty Repairs 29
- Revision History 30
- Chapter 1: Product Features 31
- CSD Operation 32
- Improved OEM Features 33
- Set up Idle Mode Text 34
- Menu Selection 34
- Call Control by SIM 34
- TCP/UDP IP Connection 35
- Creating UDP/IP Connections 36
- Features and Benefits 37
- Technical Description 38
- Overview 38
- Short Message Service (SMS) 41
- Character Sets 43
- AT Commands Summary 45
- AT Commands Overview 57
- AT Commands Protocol 58
- AT Commands Structure 59
- Results Code Structure 60
- Command Token Types 62
- Command Argument Types 63
- Command Mode Types 63
- Aborting Commands 64
- Modem ID 65
- +CIMI, Request IMSI 69
- +CNUM, Request MSISDN(s) 70
- Read Command 71
- Table 3-3: +CNUM Parameters 71
- Capability Reporting 72
- Receiving a Data Call 74
- Call Control AT Commands 75
- DL, Dial Last Number 78
- H, Hang-up Call 79
- A, Answer Incoming Call 81
- Indication 81
- RING/+CRING Indication 82
- Table 3-7: +CRC Parameters 82
- Table 3-8: +CLIP Parameters 84
- +CCWA, Call Waiting Command 85
- Table 3-9: +CCWA Parameters 86
- • Provisioned permanently 93
- Table 3-14: +CBST Parameters 96
- &Q, Asynchronous Mode 97
- +CHUP, Hang Up Call 98
- Connection of a Voice Call 100
- Call Status Messages 103
- +CLCC, List Current Calls 104
- Execute command enables 104
- Table 3-19: +CLCC Parameters 105
- +MCST, Call Status Messages 106
- Table 3-20: +MCST Parameters 107
- +MCST Parameters 107
- +CAOC, Advice of Charge 108
- +CACM, Accumulated Call Meter 110
- Supplementary Services 114
- Table 3-26: +CSSN Parameters 115
- Table 3-29: +CUSD Parameters 117
- AT+COLP=0 121
- AT+COLP=2 121
- Phone Books and Clock 124
- Table 3-33: +CPBS Parameters 125
- +CSVM, Set Voice Mail Server 130
- Table 3-38: +MDSI Parameters 132
- Table 3-39: +MCSN Parameters 135
- Table 3-40: +CCLK Parameters 138
- SMS Commands 139
- +CMGF, Message Format 141
- Table 3-45: +CSCA Parameters 143
- Table 3-46: +CSMP Parameters 144
- Table 3-49: +CNMI Parameters 147
- Indication) 150
- +CMGL, +MMGL, List Messages 153
- +CMGR, +MMGR, Read Message 158
- GSM03.40) 161
- GSM03.40) (Cont.) 162
- Reserved bits are ignored 163
- +MMAR, Motorola Mark As Read 165
- +CMGD, Delete Message 172
- +CMGS, Send SM to Network 174
- DCS handling 177
- Network Commands 181
- +CRLP, Radio Link Protocol 182
- Table 3-76: +CREG Parameters 183
- Table 3-77: +CGREG Parameters 185
- +COPS, Operator Selection 186
- Table 3-78: +COPS Parameters 188
- +CPOL, Preferred Operators 189
- Table 3-80: +MFS Parameters 192
- Hardware Information 193
- +MBC, Battery Charger 194
- Table 3-82: +MBC Parameters 195
- +CBAUD, Baud Rate Regulation 196
- +MTDTR, DTR Line Test Command 198
- +MTCTS, CTS Line Test Command 199
- &K, RTS/CTS Flow Control 199
- &C, Circuit 109 Behavior 200
- &D, Circuit 108 Behavior 202
- +MCWAKE, GPRS Coverage 203
- ATS97, Antenna Diagnostic 207
- +MRST, Perform Hard Reset 207
- +MIOC, Motorola I/O Configure 208
- Light control example: 209
- Table 3-95: +MIOC Parameters 209
- +MIOD, Motorola I/O Define 211
- Table 3-96: +MIOD Parameters 212
- Table 3-97: Keypad GPIOs 212
- Table 3-98: +MMAD Parameters 215
- +MPCMC, Continuous PCM Clock 217
- Table 3-99: +MPCMC Parameters 218
- Audio Setup 220
- HeadSet mode 221
- Idle mode 221
- Basic Audio Setup Commands 222
- +CLVL, Loudspeaker Volume 223
- S94, Sidetone Effect 225
- S96, Echo Canceling 226
- +MAPATH, Audio Path 227
- Figure 3-6: Audio Paths 228
- +MAVOL, Volume Setting 230
- +MAMUT, Input Devices Mute 232
- +MAFEAT, Features Selection 233
- General Audio Commands 234
- +CALM, Alert Sound Mode 235
- +CRTT, Ring Type Selection 237
- +VTD, Tone Duration 239
- Access Control Commands 241
- Table 3-120: +CPIN Parameters 243
- +CPWD, Change Password 247
- +CLCK, Facility Lock 248
- Table 3-124: +CLCK Parameters 249
- Table 3-125: +EMPC Parameters 252
- Modem Register Commands 254
- Q, Result Code Suppression 255
- E, Command Echo 256
- S, Bit Map Registers 258
- Table 3-131: S2 Parameters 260
- \G, Software Control 261
- \J, Terminal Auto Rate 261
- \N, Link Type 261
- +CBAND, Change Radio Band 261
- Sleep Mode Commands 263
- Sleep Mode AT Commands 264
- Sleep Mode HW Signals 264
- WAKEUP-IN 265
- Line (pin #16) 265
- Line (pin #21) 265
- Error Handling Commands 270
- Table 3-139: +CMEE Parameters 271
- Table 3-140: +CME Errors 272
- Table 3-141: +CMS Errors 274
- Table 3-142: +STK Errors 275
- +CEER, Extended Error Report 277
- Table 3-143: +CEER Parameters 278
- UI (User Interface) 280
- &V, View Configuration 285
- &W, Store User Profile 286
- AT&W0 287
- AT&W1 287
- &Y, Default User Profile 288
- +CLAN, ME Language 289
- Table 3-149: +CLAN Parameters 290
- +CIND, Indicator Control 291
- GPRS Functionality 294
- GPRS Commands 294
- +CGDCONT, Define PDP Context 296
- For example: 297
- +CGATT, GPRS Attach or Detach 301
- +CGPADDR, Show PDP Address 302
- Table 3-159: D*99 Parameters 307
- +CGPRS, GPRS Coverage 308
- Customer 310
- Application 310
- STK Mechanisms 311
- +MTKR, Profile Download 311
- Profile Structure 312
- Table 3-183: +MTKE Parameters 321
- Table 3-185: + 323
- Send DTMF 327
- Set Up Event List 329
- Language Codes 332
- +MTKM, Motorola ToolKit Menu 336
- Control are modified 338
- Table 3-193: +MTKC Parameters 338
- +MIPCLOSE, Close a Socket 346
- +MIPSEND, Send Data 348
- +MIPSTAT, Status Report 352
- MIPXOFF, Flow Control - Xoff 352
- MIPXON, Flow Control - Xon 353
- • Power Up - 0 355
- +MSDNS, Set DNS IP Address 363
- Table 3-212: 367
- NOP - Compatible 368
- Chapter 4: Using the Commands 369
- GPRS VoiceCSD Data 370
- G24 Network Connection 371
- Test G24 Communication 371
- G24 Phonebook Download 371
- Status (Optional) 371
- RS232 Lines Setup 372
- Test G24-L Communication 373
- Basic Configuration 373
- 1. Baud setting example: 374
- SIM Card Status 375
- G24-L Network Connection 376
- Terminal Synchronization 377
- Call Control 382
- Voice Call Manipulations 384
- Conference Call 385
- Data Call 386
- Establishing GPRS PDP Context 387
- Using the ATD* Command Set 388
- Changing the Character Set 389
- Sleep Mode 390
- Get Inkey 391
- Get Input 392
- Play Tone 392
- Set Up Menu 393
- Select Item 393
- Send SMS 393
- Set Up Call 394
- Launch Browser 395
- Setup Event List 396
- TCP Data Transfer Example 397
- Xoff and Xon Example 398
- Terminal 400
- Chapter 5: Tools 401
- Tools Overview 402
- Appendix A: Reference Tables 403
- Symbol GSM (GSM 03.38) 420
- Acronyms and Abbreviations 429
- Abbreviation Full Name 431
- Numerics 435
- B - D Index 437
- N - S Index 439
- W - W Index 441
- @6802983C95@ 444
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji